Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
How do you actually feel on the subject of Installing A Bathtub?
Mounting a tub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough job. If the old tub is conveniently easily accessible, the task can move immediately; if you have to open a wall surface to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually certified on your own for the task and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Chances are you might require a professional plumber to make tube links.
This post will assist you mount a brand-new tub in your washroom if you have already gotten a new tub and also do not require to alter the plan of your previous water system pipelines.
Your tools and also material checklist ought to consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of eliminating the existing taps can be quite bothersome because of the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to carrying on to fit the new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type should be connected to the tap finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are handy in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub till the spirit level reads level.
To mount taps, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water supply and examine all joints and also new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also securing around the bath tub ought to wait up until the bath tub has been utilized a minimum of once as this will certainly settle it into its last position.
Preparing for the Installation
Firstly, the sustaining framework provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the flexible tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a stiff seal, triggering the water to penetrate the wall between the bath as well as the tiling, causing difficulties with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealer can split relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily available on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that report on Installing A Bathtub through a friend on our other web address. Enjoyed reading our blog entry? Please share it. Help other people discover it. Thanks a lot for your time. Visit us again soon.
Top Article Report this page